Tutorial

How to Cover a Cardboard Box with Scrapbook Paper

I have something a little special for you this week. I have wanted to start posting more tutorials and how-to’s, and this is a good start. This is actually a mini-tutorial because when I was transferring the pictures from my phone to my computer, something went wrong and several of them were lost. Since this is only my second attempt at a tutorial, if you have any questions, or you need a little help with a particular step please let me know!

What You Will Need:

  • A small cardboard box
  • Scissors (Or a rotary cutter and cutting mat)
  • Mod Podge
  • Paintbrush or foam brush
  • Pretty scrapbook paper (I used six, 12×12 sheets from the craft store for this box.)
  • Ruler or tape measure

IMG_7054

I forgot to take a good “before” shot of the box I was using, so just ignore the fact that I have already covered the two ends!

IMG_7065

First things first, you will need to take several measurements. I made separate lists for the interior and the exterior since I was lining the entire box. If you are only covering the outside of the box, your job will be even easier! Most of my measurements for my two boxes were pretty much the same for the inside and the outside, but it all depends on the thickness of the cardboard.

Measurements You Need:

  • Inside and outside height
  • Inside and outside length
  • Inside and outside width
  • Inside and outside bottom

IMG_7057

I decided to use my rotary cutter and mat for cutting out the different paper pieces. It was much faster. Using the interior measurements, cut out:

  •  2 rectangles = height x length
  • 2 rectangles = height x width
  • 1 bigger rectangle that is the size of the bottom of the box.

Repeat using the exterior measurements. I added about 1/2 inch to all of my measurements for the sides. That way I know I will have enough paper to overlap if necessary. It is far easier to trim down than to have to cut out a whole new piece! I had two pieces measuring 6 x 12, two pieces measuring 6 x 10, and one measuring 12 x 9. (Tip: Save dull rotary cutter blades and write “paper” on them. Even though they no longer work on fabric, they cut paper beautifully.)

IMG_7058

 

Before you start mod podging everything, make sure that the bottom piece of paper easily fits into the bottom of the box. I recommend having it slightly smaller than the box bottom just so that it will slip in smoothly later.

IMG_7059

After you have cut out your pieces of paper for the four sides and the bottom, start painting an even layer of mod podge over the back of one of the smaller pieces.

IMG_7060

IMG_7067

Once covered in mod podge, the paper will become pliable and easily be able to slip into to box. Since this is the interior of the box, make sure the edge of the paper lines up evenly with the top of the box. I made sure to have plenty of overlap along the bottom and edges. To get a nice crisp corner, you may have to make a few small snips into the edges of the paper. Take your time and try to have as few wrinkles as possible.

IMG_7062

Repeat the process with the opposite short side, and then move on to the longer sides. All four sides should be covered in paper before putting in the bottom piece.

IMG_7068

All the sides are covered! I decided to put a thin layer of mod podge on the bottom of the box to insure that all the little edges would stick completely. I still painted the back of the bottom paper with mod podge, so you could totally skip this step. Carefully lay the paper in the bottom, smoothing out all the wrinkles, and making sure it looks crisp and even. If you double-checked the size of your paper earlier, you shouldn’t have any trouble getting it in now.

IMG_7071

And now we move to the outside! I wasn’t quite sure how I wanted to cover the top edge of the box, but I think I would do it differently next time. For this box, as I covered the exterior of the box, I let it overhang at the top by about 1/4 of an inch. Then after I finished covering the box completely, I dabbed some mod podge along the edge and pressed that little over hang down. It didn’t turn out as smooth and polished looking as I would have liked, but it worked!

IMG_7072

The outside is much the same as the inside. Paint the back of the paper with mod podge, carefully line it up on the box, and press it out smoothly.

IMG_7073

To get your corners nice and crisp, clip into the corner of the paper after it is pressed on to the box, like so:

IMG_7075

Next, press one side down:

IMG_7076

And then the other:

IMG_7077

Instantly beautiful corners! Repeat for the other sides. For the final piece of paper, I actually covered the actual box bottom with mod podge. That way the paper wasn’t as floppy, and I was able to lay it down exactly where I wanted it.

IMG_7080

And you’re done! Step back and admire your handiwork.

IMG_7114

IMG_7111

And then fill it with all the things! It works great for holding yarn, picture books, toys, various craft notions, and what ever other small items need a new home.

IMG_7104

IMG_7106

I’m using mine to hold my stash of zippers, elastic, and velcro. Now that I have a pretty box, I can store them on the shelf instead of under the bed! It makes it much easier to access them.

IMG_7105

That’s all from me today! I hope you enjoyed the mini-tutorial. Hopefully I can come up with a few more to share over the next couple of months.

Have a jolly day!

~Emily

Advertisements

I'd love to hear any thoughts or comments!

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s